Industrial Chain and Sprocket Manufacturer

Home / All / Sprocket / 81X Sprocket: How to Order the Right One in One Round

81X Sprocket: How to Order the Right One in One Round

Nov 11,2026

What is 81X sprockets

An 81X sprocket is the wheel that carries an 81X lumber conveyor chain. 
The pitch is 66.27 mm, so each tooth is a wide pocket rather than a fine tooth. The teeth are hardened, and the body is not: induction-hardened flanks at 45–55 HRC resist grit, while the plate stays tough enough not to crack when a chain jumps.
Where they sit: green chain, sorter feed, transfer and trimmer infeed, log deck, and take-up.
81X Conveyor Chain and Sprocket

81X Series Conveyor Chain 66.27mm Pitch

81X Lumber Conveyor Chain
Match your chain number in the first column before you read anything else. Find your chain in the column before you think about the sprocket.
Chain No.
Roller Dia.
Inside width
Plate t
Tensile Q
mm
mm
mm
kN/lbf
23.00
27.00
4.00
106.7/24250
23.00
27.78
7.94/5.55
151.9/34523
23.00
27.00
6.30
83.3/18927
23.00
27.78
7.94
191.1/43432
23.00
27.00
7.60
152.0/34545
Full 81X series conveyor chain dimensional data for each size → 81X Lumber Conveyor Chain

The three sizes that decide whether it fits

A sprocket cut for the wrong variant will bolt on. It will even run. It just will not last, and it usually takes the chain with it. These are the three checks, in the order we run them.
1. Roller diameter
81X, 81XH, 81XHH and 81XHS run a 23.00 mm roller. The 81XHE runs a 22.20 mm. The tooth space is cut so the roller sits in a curved seat; put a 22.20 mm roller in a seat cut for 23.00 mm and the load lands on two lines instead of the whole arc. The seat work-hardens, the tooth hooks, and the chain starts climbing. Half a millimetre does that.

2. Inside width
27.00 mm on 81X, 81XHE and 81XHS; 27.78 mm on 81XH and 81XHH. Cut it too narrow, and the side plates polish the sprocket face; too wide, and the chain rocks and wears the teeth unevenly.

3. Plate thickness
4.00 mm on 81X, 6.30 mm on 81XHE, 7.94 mm on 81XH and 81XHH, 7.60 mm on 81XHS. The face of the sprocket has to clear the thicker plates. This mismatch is the most common issue when a plant upgrades its chain to a heavier variant and keeps the old sprockets.

81X Sprocket Tooth Counts for Applications

81X Sprocket
81XC8 Sprockets Drawing
Teeth
Outside diameter (mm)
Where it usually goes
8T
199.8
Tail shaft, take-up - slow lines only
10T
243.7
Short transfers, slow green chain(wet lumber)
12T
287.1
The conveyor that takers freshly sawn, wet lumber to the sorter
14T
330.1
General conveying, moderate speed
16T
372.9
Drives, longer conveyors
18T
415.6
Smoother running at higher speed
20T
458.2
Main drives
24T
543.1
Large heads, high-speed lines
Our advice in one line: 
Up to about 0.5 m/s, you can use 8T to 10T; 
Between 0.5 and 1.2 m/s, go to 12T or more; 
Above that, 15T and up. 
If the sprocket is on a shaft that will not come out, tell us — a split or taper-bush design can save a day of dismantling.

Is it the sprocket or the chain? A five-minute check

Before you order anything, look at the teeth. Each wear pattern below points to one cause, and only one of them is solved by buying a sprocket.

▶ Hooked tooth tips. 
The roller seat has worn through, and the chain is climbing the tooth. Replace the sprocket — and measure chain pitch before you do, because a chain stretched past 2% will hook the new sprocket in weeks.

▶ Polished, bright tooth faces. 
The side plates are rubbing. That is an inside-width mismatch: an 81X chain on a sprocket cut for a narrower variant, or the reverse. Check b1 before you reorder.

▶ A step worn into the tooth root. 
The roller diameter does not match the seat — the classic 81XHE (22.20 mm) on an 81X (23.00 mm) sprocket. No adjustment fixes this; the tooth space has to be recut.

▶ One side of every tooth wears faster. 
Misalignment or a non-parallel shaft. Fix alignment first, or the replacement will fail the same way.

▶ Chain jumps, but the teeth look fine. 
Elongation plus too few teeth. At 8T or 10T above 0.5 m/s, the chordal action is enough to lift the chain off the seat.

FAQ

Can one sprocket run both 81X and 81XHE?
No. 81X runs a 23.00 mm roller; 81XHE runs a 22.20 mm. The tooth space has to be cut for the roller it will actually see, so an 81XHE sprocket is a separate drawing.
Which 81X sprocket fits an 81XH chain?
One cut for 81XH: 27.78 mm inside width and clearance for 7.94 mm plates. An 81X sprocket will accept the chain and then rub the plates, which shows up as a polished, worn face within weeks.
What is the smallest bore you can put in an 8-tooth sprocket?
It depends on the hub, and the hub is the limit: an 8T has about 150 mm of root diameter. We build the 8T as a C-hub (81XC8) for that reason. Send the shaft size, and we will confirm it on a drawing.
Need an 81X sprocket quoted against the chain you already run? 
Send the chain size(81X, 81XH, 81XHH, or XHE), the tooth count, the bore and keyway, and the date the line has to be back up. We will come back with a drawing, a price, and a ship date — samples within 30 days, production in 45.

Ask CTS?

Having trouble finding the product you need? Send us an email with your question or message, and we'll quickly respond with tailored solutions. We're eager to hear from you! Expect top-notch precision, reliability, efficiency, and performance. Let's redefine excellence together.

China's professional power transmission manufacturer
We offer customized product services and free samples to meet our customers' needs.
Some of our products are mass-produced and kept in stock, ready for immediate shipment.
  • Contact CTS
    • *Email
      Full Name